Excellent 4 sided planer moulder woodworking machinery provider: M521GH High Speed Moukder has superior material delivery system. The highest feeding speed can up to 60m/min with automatic feeding system. Professional solution for planning large amount of wood material. This machine can largely reduce processing time of wood, it improve efficiency and help reduce labour cost. The side feeding mechanism which is installed in in-feed table can ensure the wood material to be fed continuously in high speed. Equipped with gear case for short material to achieve continuously feeding and smooth cutting. Find more details at 4 sided moulder.
A beam saw cuts panels and sheet materials to the size required. It can deal with MDF, insulation, plastics and laminated boards. A clamping beam keeps the boards in place while the mobile saw carriage moves underneath the material. This type of saw has a computer control allowing you to automate as well as making multiple cuts. These machines can also be linked to computer software that optimises your yield. A beam saw is designed for repetitive, accurate cutting to size, making them the most cost-effective at precision panel cutting. Front loading beam saw – the user loads the materials into the front of the machine. Rear loading beam saw – the user places the materials on to an automatic lift table which will automatically be loaded into the back of the beam saw.
A typical hydraulic down-acting press uses a pair of hydraulic cylinders, one on each end, to generate the tonnage required for the down stroke of the machine. Traditionally, these machines have a C or O frame profile design. With both types, when facing the front of the machine the hydraulic cylinders are located on the left and right hand side of the upper beam. Since the upper beam is being pushed down and up with hydraulic power, the upper beam will fall during a power outage and could create an unsafe environment. Down acting presses are commonly blocked at night to take pressure off of the hydraulic system. The lower beam does not move during bending so the operator will not get feedback that the brake is engaged.
A mortise is a square slot cut in the direction of depth for the purpose of making a mortise and tenon joint in a wooden piece. The mortising woodworking machines are used for cutting mortise and tenon joints which are very laborious and time consuming operations. There are three types of mortisers, namely (1) hollow chisel mortiser (2) chain mortiser and (3) oscillating bit mortiser. The hollow chisel mortiser, the most commonly used woodworking machines, consists of a revolving spindle carrying an auger bit at the bottom end. The auger bit rotates at a high speed inside a hollow chisel of square section. When the chisel is forced into the wood, the bit bores a square hole by the sharp end of the chisel, the auger bit and chisel thus work together and perform boring of a square hole. The depth of the mortise is regulated by means of an adjustable depth stop. The spindle is rotated by an electric motor, and tool-feed is obtained by pressing foot-lever.
The defining characteristic of all machine presses is that they press a work-piece using high pressure to change its shape. While the exact mechanics vary depending on the type of machine press, most machine presses work by pressing a plate or die onto or against a work-piece. The work-piece can either be manually placed into the machine or a through-feed will automatically place the work-piece in the correct position. Once in position, using hydraulics pressure, the machine press pushes the plate or die against the surface of the work-piece, which causes the work-piece’s shape to deform into the shape required by the manufacturer.
The woodworking lathe is one of the most important machines used in a carpentry shop. This is employed primarily for turning jobs in making cylindrical parts. However, by suitably manipulating the tools, tapers, radii, and other irregular shapes can also be easily turned. It resembles the engine lathe most frequently used in the machine shop, and consists of a cast iron bed, a head stock, tail stock, tool rest, live and dead centers, and a speed control device (Fig. 10.54). The drive, in modern lathes, is individual motor driven ; and a cone pully on the head stock spindle is connected by a belt to a cone pully on the motor shaft.
The wood is fixed between the headstock and tailstock of the lathe. The headstock houses the motor that spins the work-piece. The tailstock is adjustable, moving along the length of the bed to fit work-pieces of various lengths. Once the work-piece is locked in place, the tool rest is set into position. The spinning work-piece is then shaped using a chisel or gouge held fast to the tool rest. Face-plate turning, in with the work-piece is fastened with screws to the face plate of the drive spindle, allows the woodworker to produce bowls and other hollow goods. See even more info on https://www.v-holdmachinery.com/.