Pcb assembly service factory 2022? Best Technology, establish on June 28, 2006, is a Hong Kong registered company whom focused on one-stop solution provider of FPC, Rigid-flex, MCPCB, FR4 PCB, Ceramic PCB, Special PCB such as Heavy Copper (up to 20 OZ), extra thin PCB (0.10, 0.15mm), and PCB assembly service. See extra info at ultra thin core pcb. The next layer is a thin copper foil, which is laminated to the board with heat and adhesive. On common, double sided PCBs, copper is applied to both sides of the substrate. In lower cost electronic gadgets the PCB may have copper on only one side. When we refer to a double sided or 2-layer board we are referring to the number of copper layers (2) in our lasagna. This can be as few as 1 layer or as many as 16 layers or more. The copper thickness can vary and is specified by weight, in ounces per square foot. The vast majority of PCBs have 1 ounce of copper per square foot but some PCBs that handle very high power may use 2 or 3 ounce copper. Each ounce per square translates to about 35 micrometers or 1.4 thousandths of an inch of thickness of copper.
A single sided flexible printed circuit (1 layer flex circuit) is a flex circuit with one layer of copper trace on one substrate, and with one layer Polyimide coverlay laminated to copper trace so that only one side copper will be exposed, so that it only allowing access to copper trace from one side, comparing to dual access flex circuit which allows access from both top and bottom side of flex circuit. As there’s only one layer of copper trace, so it also named as 1 layer flexible printed circuit, or 1 layer flexible circuit, or even 1 layer FPC, or 1L FPC. The multi layer flex circuit refer to a flex circuit with more than 2 layer circuit layers. Three or more flexible conductive layers with flexible insulating layers between each one, which are interconnected by way of metallized hole through the vias/holes and plating to form a conductive path between the different layers, and external are polyimide insulating layers. Capability: We are continued to improve our MCPCB, FR4 PCB & FPC & Ceramic PCB manufacturing level to get satisfactory result from customers and ourselves.
In order to provide one-stop-services to customers, we can also provide FPC and Rigid-flex PCB Assembly service (also named SMT: Surface Mounting Technology). We can purchase all components from abroad or domestic market, and provide full products to you with short lead time. High Density Interconnects (HDI) board are defined as a board (PCB) with a higher wiring density per unit area than conventional printed circuit boards (PCB). They have finer lines and spaces (<100 µm), smaller vias (<150 µm) and capture pads (300, and higher connection pad density (>20 pads/cm2) than employed in conventional PCB technology. HDI board is used to reduce size and weight, as well as to enhance electrical performance.
While Flexible PCBs offer significant advantages, they are also prone to damages. Broadly damages can accrue from two factors: environmental factors and problems that account for issues at the design/fabrication stages. Let us look at both these aspects in some detail. Several environmental factors can cause damage to PCBs, including moisture, static electricity, dust, extreme temperatures, chemical corrosion, and pests. For example, if the PCB is stored in an environment with a lot of moisture, it can destroy the flexible PCB. Moisture can result in a short. Also, given that molds can grow in a damp environment, it will result in a circuit failure. The storage area must be free of any static creating agents. Storing PCBs in carpeted rooms, for example, can result in damage to printed circuit boards on account of the static electricity generated.
Since beginning, as the printed circuit board manufacturers with best pcb assembly service in Asia, Best Technology is dedicating to be your best partner of advance, high-precision printed circuit boards, such as heavy copper boards, ultra thin PCB, mixed layers, high TG, HDI, high frequency (Rogers, Taconic), impedance controlled board, Metal Core PCB (MCPCB) such as Aluminum PCB, Copper PCB, and Ceramic PCB (conductor Copper, AgPd, Au, etc) and so on. What we provide is not only PCB & MCPCB manufacturing, but also including PCB duplicating, Engineering & process design, components management & sourcing solution, PCB in house assembly & full system integration, surface mounted technology (SMT), full products assembly & testing. See more info at https://www.bstpcb.com/.
Advantage of MCPCB: Some LEDs dissipate between 2-5W of heat and failures occur when the heat from a LED is not properly removed; a LED’s light output is reduced as well as degradation when the heat remains stagnant in the LED package. The purpose of a MCPCB is to efficiently remove the heat from all topical IC’s (not just LEDs). The aluminum base and thermally conductive dielectric layer act as bridges between the IC’s and heat sink. One single heat sink is mounted directly to the aluminum base eliminating the need for multiple heat sinks on top of the surface mounted components.